BaBylissPRO FXONE LO-PROFX Grey Trimmer

The BaBylissPRO FXONE LO-PROFX Grey Trimmer (FX729E) is a low-profile finishing trimmer for lines, edges and close detail -- a fully exposed Blue Titanium T-blade on the interchangeable FXONE battery that every FXONE tool shares. It is cordless, ultra-low-profile and finished in grey, made to sit light in the hand for the sharp, controlled detail work that defines a cut.

At a glance

What it is: FXONE LO-PROFX low-profile T-blade finishing trimmer, grey
Best for: Lines, edge-ups, necklines and close detail
Motor: High-torque digital motor, 6,800 RPM
Blade: Fully exposed Blue Titanium standard-tooth T-blade, 360-degree, zero-gap adjustable
Power: Interchangeable snap-in FXONE Li-ion, cordless, up to 3 hours, dual-voltage base
Handling: Quick battery release, 4-stage LED ring, ergonomic grip
Profile: Ultra-low-profile metal shield cover, grey finish

Why a low-profile finishing trimmer

A clean cut is made in the detail -- the lines, the edge-up, the neckline. The FXONE LO-PROFX trimmer keeps a low, flat profile and a fully exposed T-blade, so you can see exactly where the blade meets the skin and steer it right up to a crisp edge. Because it runs on the shared FXONE battery, it drops into the same charging system as the rest of your FXONE tools -- one battery type across the kit, no separate charger to track. It is the detail tool that finishes what the clipper starts.

Key features

High-torque digital motor: a high-torque digital motor holds a steady 6,800 RPM for clean lines through coarse and fine hair alike.
Exposed Blue Titanium T-blade: a fully exposed 360-degree Blue Titanium standard-tooth T-blade, zero-gap adjustable, for maximum visibility and a close, defined line; the Blue Titanium runs at a lower blade temperature.
Shared FXONE battery: the interchangeable snap-in FXONE Li-ion gives up to 3 hours cordless, with a quick-release button and a 4-stage LED ring; the same battery fits every FXONE tool.
Low-profile metal build: an ultra-low-profile metal shield cover and an ergonomic grip keep it light and precise, charged on the included dual-voltage base.

What to expect

This is a finishing trimmer -- lines, edge-ups, necklines and close detail, not bulk cutting. It runs cordless on the snap-in FXONE battery and tops up on its dual-voltage base; there is no corded pass-through while cutting. It is not a fade clipper or a shaver: pair it with the matching FXONE LO-PROFX grey clipper (FX829E) for the bulk and fade, and an FXONE foil shaver for the finish -- all three share the same FXONE battery.

Who it is for

Barbers and stylists who want a low-profile detailing trimmer on the shared FXONE battery system.
Lines and edge-ups: the exposed T-blade works right up to a clean, defined edge.
FXONE users who want one battery type across every tool in the kit.

Who it is not for

If you need bulk and fades: add the matching FXONE LO-PROFX grey clipper (FX829E), which handles the cut and blend.
If you want the fuller all-metal build: the FXONE All-Metal Gold and Black trimmers run the same FXONE battery in a heavier metal body.
If you need corded running: the trimmer is cordless-only and runs on the snap-in battery.

Professional tip

Set the blade to zero-gap for the sharpest lineup and let the exposed T-blade do the seeing -- hold it flat against the skin and work to the edge while the shape is fresh. Keep a second FXONE battery charged on the base; because every FXONE tool shares the battery, a spare keeps the whole kit moving.

How to use

Charge the FXONE battery fully on its dual-voltage base before the first use.
Snap the battery into the trimmer and adjust the blade toward zero-gap for a closer line.
Hold the exposed T-blade flat to the skin and outline the hairline, neckline and edges.
Work in small, controlled strokes for a clean, defined edge.
Oil the blade lightly after use and brush out the cut hair.
Return the battery to its base so the trimmer is ready for the next cut.

Safety: The T-blade is fully exposed and sharp -- keep fingers clear of the cutting edge and store the trimmer with its guard on. This is a grooming tool, not a wet shaver: keep it and its base away from water and do not immerse them. Charge only with the supplied dual-voltage base, keep the battery away from heat, and store the trimmer out of reach of children.

Care and maintenance

Brush the cut hair from the blade after every use and add a few drops of clipper oil along the teeth to keep it running smoothly and at a lower blade temperature. Re-set the blade to zero-gap with the supplied tool if it drifts, and fit a matching BaBylissPRO replacement blade from the BaBylissPRO accessories page when it dulls. Charge the FXONE battery on its dual-voltage base and keep the quick-release contacts clean. The FX729E shares its interchangeable FXONE battery with the wider FXONE range, pairs with the FXONE LO-PROFX grey clipper (FX829E) for the cut and fade, and works alongside the BaBylissPRO Levante dryer to finish the look.

In short

Low-profile finishing trimmer: a fully exposed Blue Titanium T-blade for lines, edge-ups and close detail.
On the FXONE battery: 6,800 RPM, cordless, up to 3 hours on the shared interchangeable FXONE battery.
Grey, travel-ready: ultra-low-profile metal, dual-voltage base, easy to pair with the matching clipper.

Complete your FXONE kit

BaBylissPRO FXONE LO-PROFX Grey Clipper FX829E -- the matching clipper -- bulk, tapers and fades
BaBylissPRO FXONE LO-PROFX Grey Duo -- the clipper and trimmer together as the matched duo
BaBylissPRO Levante Hair Dryer 2100W -- lightweight professional dryer to finish the look

Frequently asked questions

Does this trimmer share a battery with other FXONE tools?

Yes. The FX729E runs on the interchangeable FXONE Li-ion battery that snaps into every FXONE tool, so one battery type powers your whole kit. It ships with an FXONE battery and a dual-voltage charging base, and a spare battery from another FXONE tool drops straight in, so you can keep working while one charges.

Can I use it abroad?

Yes. The charging base is dual-voltage, so it works on any mains worldwide -- you only need a plug adapter for the socket shape, not a voltage converter. An adapter changes the plug; it does not change the voltage, and the dual-voltage base handles the rest.

Can I run it with a cord plugged in?

No. The trimmer is cordless-only and runs on the snap-in FXONE battery; there is no corded pass-through while cutting. You charge the battery on its base between uses, and a second FXONE battery lets you keep working while one charges.

Is it best for lines or for bulk?

It is a finishing trimmer, built for lines, edge-ups, necklines and close detail with its fully exposed Blue Titanium T-blade. For bulk removal, tapers and fades, use the matching FXONE LO-PROFX grey clipper (FX829E); the trimmer is the detail tool that finishes the cut.

How do I keep the blade cutting well?

Brush out the hair and add a few drops of clipper oil along the blade after each use. Re-set the blade to zero-gap with the supplied tool if it shifts, and fit a matching BaBylissPRO replacement blade from the BaBylissPRO accessories page once it dulls. Regular oiling keeps it running smoothly and at a lower blade temperature.

Is it a clipper or shaver too?

No. The FX729E is a finishing trimmer -- it lines and details, but it is not a fade clipper or a shaver. For bulk and fades add the matching FXONE LO-PROFX grey clipper (FX829E), and for a foil-close finish add an FXONE foil shaver; all three share the same FXONE battery.

Need help with your order? Visit our customer service center & online shopping FAQ for answers on shipping, returns, guarantees, payment security and everything else about your purchase.