BaBylissPRO FX3 DLC Titanium Fade Blade

The BaBylissPRO FX3 Fade Blade is the genuine DLC Titanium replacement fade blade for the BaBylissPRO FX3 Professional Clipper. It drops into the FX3 and brings back the flat, elongated cutting edge that builds clean fades and blends -- a hard DLC-over-titanium finish that stays sharp and glides with low friction. When your FX3 blade dulls, this is the part that puts a fresh edge back on the clipper.

At a glance

Genuine DLC Titanium fade blade for the BaBylissPRO FX3 clipper
Flat, elongated fade edge for vertical fading and clean blends
DLC over titanium: hard, wear-resistant, low-friction
BaBylissPRO ref FX903BME

Why this blade

The blade is the one part of a clipper that wears, and a dull fade blade drags and skips instead of melting one length into the next. This is the FX3 clipper's own fade blade -- a flat, elongated surface built for the vertical, scooping motion a fade needs. Keep a fresh one in your kit and the FX3 lays clean, seamless transitions again.

Key features

It is a fade blade: a flat, elongated cutting surface that supports the vertical cutting motion barbers use to graduate from skin to length. The finish is DLC (Diamond-Like Carbon) over titanium -- DLC is a hard, wear-resistant, low-friction coating, and titanium is a high-strength base that holds an edge. Together they help the blade glide, resist wear and run at a lower temperature through back-to-back fades. It is the genuine FX3 part, seating and aligning the way the original did.

What to expect

Fitted to the FX3, it cuts a clean, defined fade again -- the melt you had when the clipper was new. The low-friction DLC surface glides rather than drags and helps keep the blade cooler over a long day. It is a like-for-like replacement, so nothing about how the FX3 handles changes; it simply fades sharp again.

Who it is for

Barbers running the BaBylissPRO FX3 Professional Clipper who want a fresh fade edge
Pros replacing a dull, chipped or worn FX3 fade blade
Anyone who wants the durable, low-friction DLC titanium finish for back-to-back fading

Who it is not for

Any other clipper -- this is the FX3 clipper's own blade; it does not fit the FX8700 / FX825 2-hole clipper blades or any trimmer
Zero-gap outlining and hard lines -- a fade blade melts lengths; detailing is trimmer work

Professional tip: keep a spare FX3 blade boxed and lightly oiled in your kit. Dropping in a fresh edge before a big fade booking is far quicker than fighting a dull one halfway through a cut.

How to fit it

Switch the FX3 clipper off.
Release the old blade at the front of the clipper and lift it away.
Line the new blade up on the mount and press it on until it clicks into place.
Add a drop of clipper oil across the teeth.
Switch on briefly to check it runs clean and even before you cut.

Safety

The blade is sharp and the teeth are exposed. Handle it by the housing, keep fingers clear of the cutting edge, and make sure it is clicked firmly onto the clipper before you switch on. Keep it out of reach of children and store it in its packaging.

Care and maintenance

Brush the hair out of the teeth and add a few drops of clipper oil after each use -- even a low-friction DLC blade needs oil to stay smooth and run cooler. This is the genuine FX3 fade blade (ref FX903BME) and it fits the BaBylissPRO FX3 Professional Clipper only. For FX3 spares and other BaBylissPRO parts, see the BaBylissPRO accessories page.

In short

Genuine DLC Titanium fade blade for the BaBylissPRO FX3 clipper (ref FX903BME)
Flat, elongated fade edge; hard, low-friction DLC over a titanium base
Fits the FX3 Professional Clipper only -- not FX8700 / FX825 or trimmers

Keep your FX3 fading sharp

The genuine DLC titanium fade blade drops straight into your FX3 clipper for clean, seamless blends.

BaBylissPRO FX3 shaver · All BaBylissPRO blades & replacement parts

Frequently asked questions

Which clipper does this blade fit?

It is the genuine fade blade for the BaBylissPRO FX3 Professional Clipper (ref FX903BME). It fits the FX3 clipper only -- it is not one of the 2-hole ClipperFX blades (FX8700 / FX825) and it does not fit any trimmer. Match the FX3 blade to the FX3 clipper.

What is a fade blade and what makes it different?

A fade blade has a flat, elongated cutting surface that supports the vertical, scooping motion barbers use to blend one length into the next. It is built for fades and seamless transitions rather than bulk removal or outlining.

What is DLC titanium and does it run cooler?

DLC (Diamond-Like Carbon) is a hard, wear-resistant, low-friction coating over a high-strength titanium base. The low friction helps the blade glide and tends to keep it running at a lower temperature during long fading sessions. It still needs regular oiling -- the coating reduces friction, it does not replace lubrication.

How do I fit it and keep it sharp?

Switch off, release the old blade and click the new one onto the FX3 clipper's mount until it seats. Add a drop of oil across the teeth and run it briefly to check. After each use, brush out the hair and re-oil; regular oiling keeps it cutting smoothly and running cooler.

Is it a genuine BaBylissPRO part?

Yes -- this is the genuine BaBylissPRO FX3 fade blade (ref FX903BME), so it seats and aligns in the FX3 clipper the way the original blade did. A genuine blade keeps the fit, feel and cut you expect from the clipper.

Need help with your order? Visit our customer service center & online shopping FAQ for answers on shipping, returns, guarantees, payment security and everything else about your purchase.