BaBylissPRO FXONE Gold Clipper + Trimmer Duo

The BaBylissPRO FXONE All-Metal Gold Clipper & Skeleton Trimmer Duo (FX899GE + FX799GE) pairs the two tools a barber reaches for most -- a fade clipper for bulk and blending, and a fully exposed skeleton trimmer for lining and detail -- in one matched, all-metal gold set. Both run on the same snap-in FXONE Li-ion battery, so one system powers your whole cut.

At a glance

What it is: Matched FXONE all-metal gold clipper + skeleton trimmer
Best for: Fades, tapers, lining and detail work
In the kit: FX899GE clipper, FX799GE trimmer, 2 FXONE batteries, 2 charging bases
Power: Interchangeable snap-in FXONE Li-ion, cordless, 100-240V
Blades: Gold Titanium fade blade (clipper) + exposed gold Titanium T-blade (trimmer)
Profile: Knurled all-metal housings, gold finish

Why a matched clipper-and-trimmer set

A clean cut is really two jobs. The clipper removes bulk and builds the fade; the trimmer sharpens the edges, the lineup and the detail the clipper cannot reach. Buying them as a matched FXONE set means both tools share one battery system and one look, so you swap between bulk and detail without breaking rhythm -- and without juggling two different chargers. It is the core of a professional kit, ready to grow into a full barber setup later.

Key features

One shared battery system: the same interchangeable FXONE Li-ion snaps into either tool; the kit ships with 2 batteries and 2 dual-voltage bases.
Fade clipper (FX899GE): N1 digital motor at 6,800 RPM and 515,800 cutting actions per minute, zero-gap gold Titanium MIM fade blade, 45 mm wide, cutting range 0.3-4.2 mm, a 5-position taper lever and 8 guide combs from 0.5 to 6 mm; up to 2h30 of cordless runtime.
Skeleton trimmer (FX799GE): digital motor at 7,200 RPM and 1,137,600 cutting actions per minute, fully exposed 360-degree gold Titanium T-blade, 40 mm wide, 1.6 mm, up to 3 hours of runtime, for lining and close detail.
All-metal build: knurled metal housings with a hidden hook and a magnetic hair-pocket door on each tool.
Cordless and travel-ready: both run cordless on 100-240V through the included dual-voltage bases, each with a 4-stage LED charge ring.

What to expect

This set covers the cutting and lining stages of a haircut: bulk removal, tapers and fades with the clipper, then edges, necklines and detail with the exposed trimmer. It is cordless-only -- there is no corded pass-through, so you work off the snap-in battery and top up on the base. It does not shave: for a foil-close finish on the neck and cheeks, add the matching FXONE gold shaver and you have the full trio.

Who it is for

Barbers and stylists who want a matched clipper-and-trimmer pair on one battery system.
Fade and lineup work: the clipper builds the blend, the exposed trimmer sharpens the edges.
Advanced home users stepping up to all-metal professional tools in a coordinated gold finish.

Who it is not for

If you also want to shave: add the FXONE All-Metal Gold Shaver, or step up to the FXONE Gold Trio, which includes it.
If you prefer black: the same duo comes in the FXONE All-Metal Black finish.
If you need corded running: both tools are cordless-only and run on the snap-in battery.

Professional tip

Keep a charged spare battery on the base while you cut, and rotate it into whichever tool runs low -- because the FXONE battery is shared, you are never waiting on a single pack. Work the fade first with the clipper and its taper lever, then switch to the exposed trimmer for the lineup and edges while the blend is still fresh in your eye.

How to use

Charge both batteries fully on their bases before the first use.
Snap a battery into the clipper and set the bulk length with the taper lever or a guide comb.
Blend the fade upward in small passes, flicking out to soften the transitions.
Switch to the skeleton trimmer for the lineup, neckline and detail, holding it flat to the skin for a crisp edge.
Oil both blades lightly after use and brush out the cut hair.
Return each battery to its base so the kit is ready for the next cut.

Safety: Both blades are sharp and the trimmer blade is fully exposed -- keep fingers clear of the cutting edge and store the tools with their guards on. These are grooming tools, not wet shavers: keep them and their bases away from water, and do not immerse them. Charge only with the supplied dual-voltage bases, keep the battery away from heat, and store the set out of reach of children.

Care and maintenance

Brush the cut hair from both blades after every use and add a few drops of clipper oil along the teeth to keep them running smoothly and at a lower blade temperature. Re-set the clipper blade to zero-gap with the supplied tool if it drifts, and replace the trimmer blade with the original FX707Z gold blade when it dulls. Charge the FXONE batteries on their dual-voltage bases and keep the quick-release contacts clean. When you are ready to complete the set, the duo pairs with the matching FXONE All-Metal Gold Shaver, the ready-made FXONE Gold Trio, and the BaBylissPRO Levante dryer.

In short

Two tools, one battery: a fade clipper and an exposed skeleton trimmer on the shared FXONE system.
Cut and line: 6,800 RPM clipper for the fade, 7,200 RPM trimmer for the edges.
All-metal gold, travel-ready: cordless on 100-240V, easy to grow into the full trio.

Complete your FXONE gold setup

BaBylissPRO FXONE All-Metal Gold Shaver FX79FSGE -- the matching foil shaver -- makes it the full trio
BaBylissPRO FXONE All-Metal Gold Trio -- clipper, trimmer and shaver as a ready 3-tool kit
BaBylissPRO FXONE Gold Barber Station -- the 4-tool station with the Levante dryer
BaBylissPRO Levante Hair Dryer 2100W -- lightweight professional dryer to finish the look

Frequently asked questions

Do the clipper and trimmer share the same battery?

Yes. Both run on the same interchangeable FXONE Li-ion battery that snaps into either tool, and the kit ships with 2 batteries and 2 dual-voltage charging bases. You can keep one charging while the other is in use, or rotate a fresh battery into whichever tool runs low, so one system powers the whole cut.

Can I use this set abroad?

Yes. Both charging bases are 100-240V, so the set works on any mains worldwide -- you only need a plug adapter for the socket shape, not a voltage converter. An adapter changes the plug; it does not change the voltage, and the dual-voltage bases already handle the rest.

Can I run the tools with a cord plugged in?

No. Both the clipper and the trimmer are cordless-only and run on the snap-in FXONE battery; there is no corded pass-through while cutting. You charge each battery on its base between uses, and the second battery in the kit means you can keep working while one charges.

Which tool do I use for what?

Use the clipper for bulk removal, tapers and fades -- its 45 mm gold Titanium fade blade and 5-position taper lever handle the blend. Use the exposed skeleton trimmer for the lineup, neckline and fine detail; its fully exposed 40 mm T-blade gives you the visibility to work right up to a clean edge.

How do I keep the blades cutting well?

Brush out the hair and add a few drops of clipper oil along both blades after each use. Re-set the clipper blade to zero-gap with the supplied tool if it shifts, and replace the trimmer blade with the original FX707Z gold blade once it dulls. Regular oiling keeps both tools running smoothly and at a lower blade temperature.

Is this a shaver too?

No. This duo is a clipper and a trimmer -- it cuts and lines, but it does not give a foil-close shave. For a smooth finish on the neck and cheeks, add the matching FXONE All-Metal Gold Shaver, or choose the FXONE Gold Trio, which already includes the shaver alongside this clipper and trimmer.

Need help with your order? Visit our customer service center & online shopping FAQ for answers on shipping, returns, guarantees, payment security and everything else about your purchase.